Lutron lut mlc dummey load1/23/2024 If you are having issues with your Caseta dimmers, give this a try, might just solve your issues. And it was small enough to be tucked into the back of the box. It worked! No flashing when turning on the lights and can dim up from zero with no constant flashing either using the dimmer, pico or the app. ADI :L1-LUTMLC Model : LUT-MLC Name: Lutron LUT-MLC Minimum Load Cap, White. Easy hook up, one wire to the LOAD line of the Caseta switch and the other to the neutral wire bundle. I stumbled onto the LUT-MLC I thought I would give it a try as a last resort. Played with the upper and lower dim limits of the Caseta dimmers as per some the suggestions online and that did nothing. Went online and discovered I was not the only person having flashing light issues. If I tried to dim up either with dimmer, pico or app the lights would flash constantly until they hit a higher dim level. Most LEDs are now designed to ignore this small amount of. This tiny bit of current can cause this bulb ghosting phenomenon. Caseta wireless digital smart dimmers still need to receive a small amount of power to be able to receive RF signals. When I turned on the main switches the pot lights would flash and then stay on, but turning on from pico didn't have same effect, no flash, just turned on. In most cases, when you turn a standard dimmer off, the electronics inside do not receive any power. Each pair was controlling a seperate bank of 3 LED slim 9W potlights. However, this shouldn't be a problem as the lowest power drawn in my house is 154-watts of electronics and refrigerator after I and the wife go to bed.In an attempt to avoid tricky three way switch wiring jobs I instead installed two seperate pairs of Caseta dimmers each with its own companion pico remote. According to the PD-6WCL sheet, the minimum load for the dimmer is 25W. So when I get around to finally connecting my system to the house, I will have to make sure I always have at least 80-watts of power on in the house or my controller could cause hell with the TV's and my computer and other electronics. So it looks like my 2424lv needs an ac load of a minimum of 80-watts. Use the Pico remote control either in your hand, on a tabletop pedestal or by mounting the remote directly to the wall (remote control and accessories sold separately). I'm now using a 60-watt bulb with a 20-watt LED bulb and the lights don't flicker and they come on instantly. The Caseta by Lutron In-Wall Switch provides switching of multiple load types and, when paired with Pico remote controls, allows remote control from anywhere in the space. Every time the lights would flicker and not come on until I reached 80 watts. I first noticed it when some CFL bulbs would flicker every 2-4 min while off. I checked them with a low impedance meter with NO load connected. I have 3 switches (just the ON/OFF, not dimmable) and they bleed 10-11v in the off position. I then tried a 60-watt bulb with different size LED bulbs. I'm currently having some issues with the Lutron switches. It wasn't until I increased to Load with a 100-watt incandescent light bulb that the light would come on without any flickering. Search for Lutron Caseta 3 Press and hold off button on remoteUse the Lutron app to complete ALL remaining. If you are using the switch and remote control with the LutronR Smart BridgeT follow the instructions below. So I removed the LED bulbs and connected a 40-watt incandescent bulb and got the same results. Lutron The CastaT Wireless switch can be controlled from a smartphone when used with the LutronR Smart BridgeT. So I figured the controller isn't putting out a high enough initial voltage to trigger the LED bulbs. I added 3 more 9-watt led bulbs and all the light would still do is flicker and not come on. (System not connected to the house yet) I used one 20-watt led bulb and on battery power, but all the bulb would do is flicker on and off. With respect to my house, all lights are LED so while checking my system before connecting the array panel. Using a LUT-MLC on a forward phase dimmer will cause the dimmer to fail prematurely and is not recommended by Lutron. But yesterday I brought the system home so I could connect solar panels to the system as I don't have access to the direct sun at my hanger. For several months the 2424lv has been sitting on my workbench in my hanger and working flawlessly. Up until this time I have been using a 140-watt fan or 100-watt heat lamp as my load from my 2424lv. I have the MTTP 2424LV-msd (all-in-one) controller/inverter. Lutron sells at least one model of dimmer with a neutral connection, and they push it heavily if you have available neutral wires in your installation. They can also be designed to use the neutral. Found out something about a little solar system. And then dimmers themselves are powered by leaking a small amount of current to the load.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |